disk prepoznat kao generic?

[ReaKtoR_]

uradjeno kloniranje disk to disk sa starog maxtor 80G(ATA) na novi maxtor 160G (SATA150)...nakon toga bootuje sa sate ali stari disk nije izvadjen...vide se 4 particije C,D,E,F + dve optike G,H i klonirane particije I,J,K,L...nakon sto je stari disk izvadjen (posto je nepotreban vise) particije su ostale I,J,K,L.

pitanje: kako promeniti drive latter?

drugo...nakon prvog boota sa novim diskom windows nasao novi hardware i instalirao ga je...u trayu se pojavljuje ikona za safely remove hardware gde disk prepoznaje kao generic volume...ploca je GA-K8NS rev 2.0...svi drajveri za cipset su vec instalirani...treba posebno neki driver za satu? zasto disk prepoznaje kao generic?

hvala

 

[ivande]

- drive letter mozes promeniti u
control panel > administrative tools > computer management > disk management > drive letter change

- ja licno nemam iskustva sa tim, ali imas u ovoj sobi cini mi se nekoliko threadova na tu temu

 

[Jurke]

- drive letter mozes promeniti u
control panel > administrative tools > computer management > disk management > drive letter change

Tako nece moci da promeni drive letter particije na kojoj je sistem, ostale moze kako hoce...
Za promenu drive letter sistemske particije mora upotrebiti nesto drugo, kao na primer Partition Magic, ali oprez sa njim jer su se neki zalili da im je napravio veliko s**nje.

 

[Panos]

Tako nece moci da promeni drive letter particije na kojoj je sistem, ostale moze kako hoce...
Za promenu drive letter sistemske particije mora upotrebiti nesto drugo, kao na primer Partition Magic, ali oprez sa njim jer su se neki zalili da im je napravio veliko s**nje.

Evo leka:

Change the System/Boot Drive Letter
Warning Serious problems might occur if you modify the registry incorrectly by using Registry Editor or by using another method. These problems might require that you reinstall your operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.
1. Make a full system backup of the computer and system state.
2. Log on as an Administrator.
3. Start Regedt32.exe.
4. Go to the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices
5. Click MountedDevices.
6. On the Security menu, click Permissions.
7. Verify that Administrators have full control. Change this back when you are finished with these steps.
8. Quit Regedt32.exe, and then start Regedit.exe.
9. Locate the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices
10. Find the drive letter you want to change to (new). Look for "\DosDevices\C:".
11. Right-click \DosDevices\C:, and then click Rename.

Note You must use Regedit instead of Regedt32 to rename this registry key.
12. Rename it to an unused drive letter "\DosDevices\Z:".

This frees up drive letter C.
13. Find the drive letter you want changed. Look for "\DosDevices\D:".
14. Right-click \DosDevices\D:, and then click Rename.
15. Rename it to the appropriate (new) drive letter "\DosDevices\C:".
16. Click the value for \DosDevices\Z:, click Rename, and then name it back to "\DosDevices\D:".
17. Quit Regedit, and then start Regedt32.
18. Change the permissions back to the previous setting for Administrators (this should probably be Read Only).
19. Restart the computer.

uradjeno kloniranje disk to disk sa starog maxtor 80G(ATA) na novi maxtor 160G (SATA150)...nakon toga bootuje sa sate ali stari disk nije izvadjen...

Trebao si da skines stari disk i onda da butujes...

 

[masnikosa]

Imam istu plocu.Pogledaj pod ide kontrolerima kako ti je prepoznao kontroler ako te nervira to za generic .treba da pise nvidia nforce 3 sata controler.To zna da ne instalira nego koristi od vindovsa pa ti ni id diska ne ocita.

 

[gsimon]

posle kloniranja uvek ostavi samo 1 disk
drugi ukloni....

 

[ReaKtoR_]

hvala na savetima..sad je sve ok