Greetings 2 all
Neka ovo citaju samo oni kojima se u 3DS MAX-u material editor prozor otvara za vise od 4s.
Kada sam instalirao Gf4 4200 bio sam vrlo nezadovoljan performansama ali mi je bilo glupo da se bunim.
U mom slucaju problem je bio sledeci:
Iako sam od ranije na Discreet-ovom forumu citao o problemu sa Nview nisam primetio da se skot uvlaci i u Control panalFX .
Da ne duzim, posle iskljucivanja istog (nview) u Control panel-u u nekim testovima 3DS MAX radi i do 3 X brze (kome trebaju 2 monitora preporucuje se UltraMon).
U svakom slucaju evo preporuka za brzinu u MAX-u sa Discreet-ovog foruma.
(ne prevodim jer pretpostavljam da se bez engleskog MAX ne moze koristiti)
<<<<<<<<<<
You have to setup the card in the following manner to get it functioning at
spec.
First off.....
1) Use the Add/remove hardware wizard to remove the card. Do this to remove
all previous nvidia drivers in the system. I don't care if your using the
latest driver or not, just do it .
2) Without rebooting, run a registry cleaning program, like regcleaner (Do a
search on google for regcleaner), and remove all invalid entries. This helps
clean up the old driver files.
3) Download the latest nvidia drivers. DO NOT doubleclick the EXE. Install
winzip or another extraction program, and EXTRACT the files to a directory.
4) Reboot
5) When the found new hardware wizard pops up, point it to the directory of
the files you extracted.
6) Stage 1 is done. Yay.
7) After installing the drivers and rebooting, you have to optimize the
card. This involves.....
Editing the 3dsmax oglfx.ini file and adding a 1 after Multitexture=1
(Instead of =0) Do a search in your max directory for OGLGFX.INI
Going into display properties and navigating to the nvidia rollout and
editing the following....
Under OGL
Fast linear mip mapping on, Dual Planes= ON (Try off if speed doesn't
improve)
Anisophic filtering OFF
VSYCH OFF
If there is a texture slider for Quality/Performance, flip to performance.
Turn off Hardware OVERLAYS (If you don't have this, its ok
)
Under Antialiasing...Set to Manual SET TO OFF.
Under Nview, Set to Disabled. If you want to learn out to setup the nvidia
card to use dual displays AND do it in a fast and efficent manner, check out
the discreet forum at support.discreet.com under hardware_OS. Lots of theads
on the subject. By default however, nview can cause up to a 600% performance
loss, basically crippling the card.
Next step... Don't go in max yet. Its time to hit up the computers bios.
Reboot, press del upon booting, look for the AGP setting section....[most
boards have these set to compatability mode by default]
Set AGP Size to 64
Fast Writes Enabled
AGP 4X Enabled
If your feeling lucky, you can try the Master Write Enabled (Different on
each board)
Now boot back into windows 2000.
Make sure if its a via motherboard, that you have the latest via 4 in 1
drivers. If its amd760 or 761 get the latest amd drivers. If its an intel
board, you'll have to download the intel agp and chipset drivers.
If its win2k, you need service pack 2, along with all the compatbility
updates.
If your performance is still slower after all that, then you've got a
hardware/system problem...(Aka your trying to run a top of the line
accelerator on a PII400, or something is seriously wrong with your system,
like a device is sharing the video IRQ)
MAKE SURE....
to disable nview in the control manual. Completely disable it. All the way,
yes thats right, disable nview in the control panel...did I mention to
disable nview in the control panel?
There ya go, enjoy.
>>>>>>>>>>>>>>
Nadam se da ce ovo nekome biti korisno (meni jeste).
